塑膠熔融指數測定機的詳細信息
MELT FLOW INDEXER
本機適用于熔融黏度較低之熱塑性塑膠之品質管制。測定方法是在規定溫度，荷重，及活塞于圓柱筒內位置等條件下，以計時測量方法測定熔融塑膠擠過一規定長度與直徑之細孔模之速率，用來判別制程當中聚合物流率之均勻性。本機符合 ASTM，ISO，JIS，CNS 規范 A 法測定標準，可選擇定時自動切料或按鍵切料。適用于流率在 0.15 至 50g/10 min 間之材料。
This tester covers measurement of the rate of extrusion of molten resins through a die of
specified length and diameter under prescribed conditions of temperature，load and piston
position in the barrel for measuring the flow rates of polymer in producing process。This
tester is complied with ASTM，ISO，JIS，CNS method A。The specimen can be cut off
automatically either by a presetting specified time interval or by manually pressing the
control key。It is applicable to test the material with a flow rates that fall between 0.15
and 50g / 10min。 溫度控制 Temperature control
常溫 ~ 400℃，PID 控制， ±0.1℃（含超溫保護）Room temperature ~ 400℃±0.1℃，PID control，include overheat protected 砝碼 Weight
1000g，2160g，3800，5000，7160，10000g，12500g，21600g ( 任選一種 equipped with one of them ) 自動切料裝置Auto cutoff device 自動切料，手動切料可選擇 Auto / manual selection 設定時間 Timer 0.1 ~ 999.9min 任意設定 圓柱筒 Cylinder Ø9.5504 ± 0.0076mm 活塞 Piston Ø9.4742 ± 0.0076mm 細孔模 Die外徑 9.5 ± 0.02mm，孔徑 2.0955 ± 0.0051mm，長度 8.00 ± 0.02mm Out diameter 9.5 ± 0.02mm，Inner diameter 2.0955 ± 0.0051mm， Length 8.00 ± 0.02mm 電源 Power AC 220V / 50Hz
MELT FLOW INDEXER
本機適用于熔融黏度較低之熱塑性塑膠之品質管制。測定方法是在規定溫度，荷重，及活塞于圓柱筒內位置等條件下，以計時測量方法測定熔融塑膠擠過一規定長度與直徑之細孔模之速率，用來判別制程當中聚合物流率之均勻性。本機符合 ASTM，ISO，JIS，CNS 規范 A 法測定標準，可選擇定時自動切料或按鍵切料。適用于流率在 0.15 至 50g/10 min 間之材料。
This tester covers measurement of the rate of extrusion of molten resins through a die of
specified length and diameter under prescribed conditions of temperature，load and piston
position in the barrel for measuring the flow rates of polymer in producing process。This
tester is complied with ASTM，ISO，JIS，CNS method A。The specimen can be cut off
automatically either by a presetting specified time interval or by manually pressing the
control key。It is applicable to test the material with a flow rates that fall between 0.15
and 50g / 10min。 溫度控制 Temperature control
常溫 ~ 400℃，PID 控制， ±0.1℃（含超溫保護）Room temperature ~ 400℃±0.1℃，PID control，include overheat protected 砝碼 Weight
1000g，2160g，3800，5000，7160，10000g，12500g，21600g ( 任選一種 equipped with one of them ) 自動切料裝置Auto cutoff device 自動切料，手動切料可選擇 Auto / manual selection 設定時間 Timer 0.1 ~ 999.9min 任意設定 圓柱筒 Cylinder Ø9.5504 ± 0.0076mm 活塞 Piston Ø9.4742 ± 0.0076mm 細孔模 Die外徑 9.5 ± 0.02mm，孔徑 2.0955 ± 0.0051mm，長度 8.00 ± 0.02mm Out diameter 9.5 ± 0.02mm，Inner diameter 2.0955 ± 0.0051mm， Length 8.00 ± 0.02mm 電源 Power AC 220V / 50Hz