無轉子硫化儀
編號：GD
規格：GC7028
一. GC7028無轉子硫化儀主要技術指標
1．高傳感器：0~20N.m。解析度：0.001N.m。
2．控制系統：采用計算機控制和接口板進行數據的采集、保存、處理和打印試驗結
果及曲線處理。
3．旋轉系統：采用步進Electronics調速電機＋振幅調整器。 擺動角度：±0.5o ±1o。
4．控溫系統：采用Inteligent數字式溫控儀表，實時Automati調整PID控制參數。
溫度控制范圍 0--200℃ 、 測溫控制 ≤±0.3℃、溫度分辯率 0.1℃。
5. 數輸方式：RS232傳輸
6．顯示方式:Vulcanize－105 WIN-XP測試軟件計算機屏幕顯示，加上優良的用戶
軟件和的硬件設備使得整個測量變得方便、快捷、和愉快。
7．模腔：Cr6wv材質，合GB/T16584－1996標準要求。
8．測控方式：人性化的測控方式，鼠標即點即用或主機面板輕觸按鍵兩種試驗方式
二. GC7028無轉子硫化儀軟件功能介紹
1．測試標準化：合GB/T16584《橡膠－用無轉子硫化儀測定特性硫化》、ISO6502:
1991及AS5289－95 。
2．試品資料：設定的膠料編號名，如“外胎5號”，“RBS6“等等。用戶如需另加標題
名稱說明打印的圖紙時，可設定任何形式的標題文字說明。
3．功能的說明：人性化設計的優良功能是在測試過程中可以修改測量時間，
膠料估計20分鐘硫化完成，設20分鐘測量時間，實做11分鐘時發現9分，10分處就已經硫化完成，這時已沒要再往下做，“修改測量時間”下的20分為9分或10分，按“送出”，實驗立即停止在9或10分上，畫出完整硫化曲線，計算出數據。如果實驗做到18分，19分鐘要結束時硫化曲線仍在往上升，硫化還未完成，實驗須再往下做，否則得出的數據是錯誤的。這時可修改測量時間為25分或更多，讓實驗繼續，直到硫化完成為止。這一功能無疑大大方便了用戶，節約了寶貴時間和膠料。
4．圖形曲線尺度自動化Auto Scale，測量完成后，軟件將根據測量數值大小按0—5
Mv 0—10Mv 0-20Mv自動調整Y標度，使曲線更美觀，多曲線對比，不同的膠料，不同的曲線形狀，不同的測量時間，亦可進行對比。
5．數據庫：軟件預先設定了100個編號的數據庫。每一個庫可以存入無限組測量數據。面對幾個月幾年幾十年成千上萬組數據日后查詢方便，用戶可以將不同時間段的數據放入不同的數據庫中，設定數據庫地址的目的就在于此。
6．測試結束自動存檔，測試完畢自動求算t10、t30、t50、t70、t90、ts1、ts2、Vc1、Vc2、
扭矩、小扭矩等等。
三. GC7028無轉子硫化儀附件
1. 無轉子硫化儀一年保固書及中文操作說明書各一份。
2. 無轉子硫化儀測試軟件一份。
3. 品牌電腦一套、彩色打印機一臺。
四. GC7028無轉子硫化儀主要計數指標
1．測溫范圍：0℃－200℃
2．測溫：≤ ±0.3℃
3．控溫：≤ ±0.3℃
4．溫度分辨率：0.1℃
5．力矩量程：0－10N.m 0－20N.m
6．力矩解析度：0.001N.m
7．模腔頻率：1.7Hz
8．振幅：±0.5o ±1o
9. 環境溫度：0－35℃相對濕度<80％
10．硫化時間設定范圍：2－300min
11．配氣0.5MPa
12．電源 交流220V 800W
13．機臺尺寸：約660×580×1300mm
14．機臺重量：約210Kg。
No rotor curing
Number: GD
Specification: GC7028
A GC7028. No major technical index rheometer
1 high precision sensors: 0~20N.m. Resolution: 0.001N.m.
2 control system: adopts computer control and interface board for acquisition, storage, processing and printing node test data
Fruit and curve processing.
3 rotation system: step Electronics speed regulating motor + amplitude regulator. Swing angle: ± 0.5o ± 1o.
4 temperature control system: uses the Inteligent dial temperature control instrument, Automati real time adjustment of PID control parameters.
Temperature control range 0--200 ℃, temperature control precision is ± 0.3 ℃, 0.1 ℃ temperature resolution.
5 data tranission: the tranission of RS232
6 Display Mode: Vulcanize－105 WIN-XP test software of computer screen display, excellent user plus
Software and advanced hardware equipment makes the whole measurement becomes very convenient, quick, accurate and pleasant.
7 cavity: Cr6wv material, in line with the requirements of GB/T standard.
Control mode: 8 means of humanity, the mouse which or the host panel touch key two ways of testing
Two. No GC7028 software rotor curing
function introduction
1ISO6502:The 1 test standard: meet GB/T16584 "rubber - with no rotor curing properties of vulcanized Determination", ISO6502:
1991及AS5289－95 。
1991 and AS5289－95.
2 test data: the adhesive number set, such as "tire No. 5", "RBS6" etc.. If you need additional title
he name of the print drawings, can be set to any form of Title text.
Note 3: excellent quality functions function of humanized design can be modified measurement time during the test,
Rubber vulcanized complete estimates for 20 minutes, 20 minutes to measure time, do 11 minutes 9 points, 10 points is already finishing vulcanization, then have no need to do, just "to modify the measurement time" under the 20 points to 9 points or 10 points, according to the "send", the experiment immediately s at 9 or 10 points, to draw a complete vulcanization curve, calculate all data. If the experiment is done 18 minutes, 19 minutes to the end of vulcanization curve is still rising, curing is not complete, the experiment must be to do, otherwise the data is the error. It can modify the measurement time of 25 minutes or more, let the experiment continued, until the curing is completed. This function will undoubtedly greatly convenient for users, saving time and glue.
4 the curve scale automatic optimization of Auto Scale, the measurement is completed, the software will measure the size of the 0 - 5
Mv 0 - 10Mv 0-20Mv to automatically adjust the Y scale, the curve is more beautiful, more curve comparison, glue is completely different, the shape of the curve of different, different measured time, can also be compared.
5 database: software pre set 100 number database. Each library can be stored in the infinite set of measured data. In the months and years decades later tens of thousands of sets of data query, the user can be in different time data in different databases, this is the address of the database to set.
6 the end of the test automatically archived, testing is completed automatically calculates the T10, T30, T50, T70, T90, TS1, TS2, Vc1, Vc2,
The maximum torque, minimum torque etc..
Three. GC7028 no rotor curing accessories
1 no rotor curing one year warranty book and a copy of the Chinese operating instructions.
2 no rotor curing a special test software.
A set of 3 brand computer, a color printer.
Four. GC7028 has no major count index rheometer
1: 0 ℃ temperature range 200 ℃
2: the measurement precision is ± 0.3 ℃
3: temperature control precision is ± 0.3 ℃
4 temperature: 0.1 ℃ resolution
The 5 torque range: 0－10N.m 0－20N.m
The 6 torque resolution: 0.001N.m
7 cavity frequency: 1.7Hz
Amplitude: 8 ± 0.5o ± 1o
9: 0－35 ℃ ambient temperature relative humidity <80%
10 vulcanization time setting range: 2－300min
11 valve 0.5MPa
12 power to AC 220V 800W
13 sizes: 660 x 580 x 1300mm
14 the machine weight: about 210Kg.
